This kit and a set of Lee dies is everything you need to begin reloading. The Classic turret press is fast and convenient when loading handgun cartridges, with rates in excess of 250 rounds per hour possible. The kit includes the Pro Auto-Disk powder measure and riser, perfect for all handgun and small rifle cartridges. Large and Small Safety Primeare included making on press priming an ease. Instant change turret makes changing calibers a snap. Deactivate the auto-index and batch load the longest and largest rifle cartridges. Complementing your press kit are the case conditioning tools to prepare your brass for loading. Includes Cutter, Lock Stud, Chamfer Tool, small and large Primer Pocket Cleaner, and a tube of Lee case sizing lube. Complete it with the cartridge specific Case Length Gauge. Verify your loads with the included Lee Safety powder scale. Completing the kit is Modern Reloading Second Editionrecently revised with all new load data covering 167 cartridges with over 28,000 loads. Note: the Bench Plate system the Classic Turret Press is mounted to in the photo is sold separately.
The Lee Precision 45 ACP Pistol 4-Die Set Comes With Four Dies. This Includes Carbide Full Length Die, Bullet Seating Die, Powder Thru Expanding Die, and Universal Shell Holder. This Product also Comes With Powder Dipper and Instructions/Load Data.
The Lee Precision 6-Cavity Bullet Mold .45 Caliber blocks are machined from commercial quality aluminum and feature steel bushing and alignment pins. It is machined from aluminum blocks making them rust resistant. Aluminum molds heat up and cool down faster than iron or steel molds so good bullets can usually be produced after only a few casts. In addition, they are one-third the weight of iron or steel mold blocks for less fatigue during extended casting sessions. To ensure the best possible bullets, mold block halves are clamped together and then lathe-bored for unmatched roundness and size control. It comes with a cam operated, hard-anodized sprue plate which is held tightly with tempered spring washers at each end.
The Lee Precision Carbide 3 Die Set for .45 ACP set includes powder through expanding die, bullet seating die, and a carbide full length sizing die. This 3 die set is perfect for effective and efficient re-use of your .45 ACP ammunition. The dies have been packaged in an air-tight, low profile box that will preserve the integrity of your dies and keep them organized and at the ready.
Lee Loader is a complete reloading system, kit includes everything needed to reload 45 Auto. except a rubber mallet. Please note: the Classic Lee Loader neck sizes only. This is not recommended for semi, pump and lever action guns.
Lee #2L Quick change shell plate for the Load-Master Press. For the 45 ACP, 30/06, 308 Win and similar cases
Lee 45 ACP/45 AUTO RIM/45 SCHOFIELD/45 WIN MAG/45 GAP Carbide Factory Crimp Die sizes the cartridge while being crimped so every round will positively chamber freely with factory like dependability The adjusting screw quickly and easily sets the desired amount of crimp. Trim Length is not critical so this extra operation takes less time than it would if cases were trimmed and chamfered. A firm crimp is essential for dependable and accurate ammunition, as it eliminates the problems of poor ignition of slow burning magnum powders.
Lee Bulge Buster Kit and appropriate Lee Factory Crimp assures your mixed brass is bulge free. This push through die adapter will quickly remove the annoying bulge rings that shell holder constrained dies simply can't reach. The Bulge Buster Kit includes: extension sleeve, push through punch, catch container and complete instructions. Works with these rimless cases: 380 ACP, 10mm, 40 S&W, 41 AE, 45 ACP, 45 GAP, and 45 Win Mag. NOTE: 9mm cases are not able to be used in the Bulge Buster because it has a slightly tapered case and the rim is not completely flush with the case. Glock Cases: We do not recommend "fixing" cases fired in pistols with unsupported chambers, because there is no way to make them safe once they have bulged. The case wall is thinned where it bulges, and resizing the outside of the case back down to the correct diameter does not restore the case back to its original thickness. If this case is fired in a pistol with an unsupported chamber again, and this thinned section of brass happens to line up with the unsupported part of the chamber, there is a high probability that the case will rupture.
Lee 45 ACP Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim.
Lee #2 Auto Prime shell holder used only in the Auto Prime. For the 25/06, 7-mm/08, 8 x 57 Mauser, 45 ACP and similar cases.